ILLUSTRATIONS ! How to Overclock and Want to Learn About Overclock and Video Card Overlock ...
1. Foreword 2. What is Overclocking? What does it do? How is it done? 3. How To Process OverClock? 4. How To Find The Cpu Limit? 5. How do we find the ram overclock limit? 6. How To Overclock Graphics Cards? 7. Cooling
Computer enthusiasts have always wanted to run their existing systems a little faster and performance. In our forum, the daoverclock section is getting a lot of attention. I prepared this study, which I think will be useful for those who are starting to work overclocking or have enough knowledge and experience but want to start.
Let's not forget this; Overclocking is under the responsibility of the creator and editors and site owners cannot be held responsible for any problems that may arise.
2. What is Overclock? What does it do? How is it done?
Now we have learned that there are 2 ways to increase the total mhz ahead of us.
The first way is to increase the speed of Fsb,
The second way is to increase the total mhz by increasing the number of multiplier times. Now we will increase the mhz value if we increase the fsb or the multiplier. .Amd processors are different in the case, they can be opened even if they are open or some methods are locked. In this case, we can have more flexible overclocking because of the possibility of playing with both values. Keep in mind that it can be achieved by increasing the reason. The reason is that at high fsb speeds, memory controller,storage devices controllers and AGP / PCI clock speeds also increase. Of course, AGP / PCI clock speeds can be troubled by high overclocks, so the stability of modern motherboards has been added to modern motherboards for stability.
Now let's start overclocking step by step.
First of all, I have to point out that our board must be manufactured for the first time for overclocking. So if you need to overclock, you need to have every feature available. There will be a lot of work and moral disruption. Of course, the work doesn't just end with the board. For overclock, we need to find a processor that is prone to this. This job is so interesting that not every processor's overclocking performance can change. You may not reach the same overclocking values even on two processors.This is primarily a matter of luck, but it is useful to learn about which CPUs and codes are more susceptible to overclocking in the predecessorclock forums and choose the processor accordingly. After choosing our processor, of course, the job does not end again; ramvar is next. In addition, since overclocked parts will increase their energy needs, we must have a quality and at least 400 watt powersupply. Of course, the most important issue is cooling. Since our overclocked system will get hotter (cpu at first), we need to have a much better cooling. In fact, overclocking is a very expensive and risky event.If you are aware, all the instruments I mentioned are more expensive than normal. there is always for.
Risky and expensive, so why do we overclock?
The quickest and most concise answer to this question is pleasure and passion. It is not possible to get rid of it once.
3. How To Process OverClock?
For Overclocking, we first need to enter the part where we can call the bios of our board. (Although there is the possibility of overclocking over Windows, I will not enter the subject because it is not a preferred style by ruggedclockers.) While opening the PC, I enter the bio by pressing the del button. In other boards, three or five are the same.
From the famous soft menu of Abit, we enter the most crucial section with cpu, ram, agp frequency and voltage settings.
As you can see above, this is our view in the default settings. All our values are as they should be.
Since we do not need default values, we set the “cpu operatingspeed” option to “user defined” so that the cpu fsb, cpu: ram ratio and the agp / pci settings are turned on. Because by playing with these values, we will do overclock.
First of all, we increase the amount of fsb a bit, I would get 250 from 200 mhz, but I tried this value directly because I trusted the CPU. Do not be in a hurry. For example, first increase to 210 mhz, then to 220. If you caught your attention, I made the cpu: ram ratio 1: 1, so why? With this cpu, it means that my rams will work synchronously at 1: 1 equally mhz. Of course, since my rams are DDR 566 (2x 283mhz), it can work synchronously with the CPU. If you do not have rams operating at these values, you should decrease this value.
(It can take place on some boards like this: CPU: RAM ratio should not surprise you)
So if you have DDR 400 rams and you are sure that your ram can not work over 200mhz, you should make this ratio as 5: 4 as in the options above so that the system does not crash. I think instead of dealing with rams first, keep your ramora at a low rate in order to find the limit of your processor, such as 3: 2. In this case, since the rams will work at lower values, they will not prevent you from determining the cpu limit.
4. How To Find The Cpu Limit?
First of all, we will increase the default voltage to where it can go in mhz. Every time we increase, you should turn the PC off and on to check its stability and most importantly, the CPU temperature. If there is no stability and warming problem, this is good news. We can continue our way. After entering the bio again and increasing the speed of the fsb, let's say that our processor has started to crash at 240 fsb. program with sandra, pc mark etc. is successful in completing tests such as set, freezing, etc. If it does not pass, if it is reset or freezing, this means that we have reached the limit of the CPU's default voltage. What are we going to do?
As seen above, increasing the CPU core voltage may help. This can help the processor, whose stability has deteriorated. While doing this, it is useful to do it little by little because overclocking is the most dangerous event voltage, excess voltage can take you directly to your CPU. In this way, after stabilization with voltage increments, we find the highest stable value that cpu can go out by going to ffsb increments. As I mentioned, we will find the most appropriate value after testing with test programs. Of course, I repeat you should keep the CPU temperature under control in all stages. Make sure that the temperature of your CPU in the default state does not increase by more than 25%. Although some boards do not read the temperature correctly, as I said, the most accurate way is the default value and the value after overclocking is not more than 25%.
5. How do we find the ram overclock limit?
Now we will find the limit of the rams. We will first find this by playing with the ram: ram ratio seen above. If our rams are already fast, DDR500 and above will not be a problem anyway, but if our rams are DDR 400 or lower, it may not be able to remove 1: 1 cpu / ram. In this case, we will have to run rams at a lower value, such as 3: 2 or 5: 4. But the right and left of these rams are uncertain, sometimes you get an oem ram DDR 400 or 366 and it normally surprises you when it has to work at these values and it can work almost at DDR 500 speeds. You will find it by trying it. You tried the same cpug and after a while the system crashed. We do not suspect the CPU, as we can limit the cpu banana. It can be beneficial to increase the ram voltage as we increase the CPU voltage.
We find the most stable and max value by increasing the ram voltage as in the picture. Of course, some rams may not like the voltage and the voltage can be reversed. We are lucky if we came across ram-loving rams, we can go up quite a bit up here. We have reached the limit in our rams, now we have come to play with ram timings, write our aggressive work with lower cl values.Low cl value means more performance since it will have a faster data cycle.In this, we make it by entering advanced chipsetfeatures from our main menu.
From here, we enable the options to be opened manually by making DRAM timing selectable.
As you can see in the picture, we are trying to reduce the ram timings here by trial and error. As I said, how low the performance. Of course, the timings that each ram can handle are different. It is not possible for me to say that I get it here. You Deneyerekbul. If the lowest ram timing we can find comes with the stability, it means that we have overclocked our rams to the maximum extent. Meanwhile, the PAT (Performance Acceleration Technology) incident, which brings another plus to the rams on the i875 chipset, can be presented under different names on the 865 chipsetboards. This is offered under the name of HyperPath in some, and the game is under the name of accelerator. When doing all these attempts, when your overclocked component is not able to digest the CPU or ram increase, your system may not lock up. Don't worry, these are common situations. The cure is to try to re-open the system by holding the insert key after waiting for five to ten seconds. Sometimes this is not a solution, then you should reset the bios with the clear cmos jumper on the board to open it at default values. (You must know your board well first. You should examine the booklet and learn what and where)
In the meantime, let me give an example from amd. One of the most famous and performance chipseti nforce2 and of course abit nf7.
As you can see in this picture, the multiplier of the processor is open and we have the opportunity to play with the multiplier as we want here. There is also the voltage of agp, which is already present in most other platforms. It is rumored to increase the stability when the display card is oc, but I could not confirm this narration, but it does not work, but of course you can try it.
6. How To Overclock Graphics Cards?
Yes, we have overclocked our system. Of course, you may not be able to overclock it. You may want to overclock your display card. There are various ways to do this. Ati or nvidia that changes according to your card. It is possible to overclock the graphics cards with various programs. The horse tool is very useful for horse cards.
When we run the Ati tool after installing it in our system, we see the interface of the program. We are increasing the ram and core-gpu speeds to the default value of our 800xx card and of course, we do this by trying the same CPU overclock slowly.
As it is seen in the picture, we find the highest stable and non-artifact value (without distortion in the image) and use it in that setting.
Nvidia cards in various programs var.riv tuner, coolbits vs.gibi.b which is a regdosya most practical from bahsedeceğim.y NEW coolbits'den.coolbits our windowsu when on clicks (registry) kayıtdefter to settled nVidia graphics card in the set is part of our drive Clock frequencies (clock frequency settings ). It is possible to set ram and core speeds separately.
Coolbits may not be enough for you. Then you can try different programs. I do not provide links for programs because they are constantly updated. There are a lot of links when you search on google.
Yes, I briefly tried to explain to the video card in overclocking. It is not just that, the tabioverclock incident is not just that. so I suggest you follow the modolay from the relevant topics.If we add this to the top, it will be mixed well.
I hope it will be useful. It is useful to remind you once again. Overclock is a risky business and only the risk belongs to the person who makes it.,
Yes, I tried to explain overclocking as simply as possible. As I mentioned, the overclocked parts require better cooling than normal since they will heat up more. The most suitable for this is to use coolers that come with cpu instead of their own heat sink.
You can add a performance fan according to your preference on this cooler. This will provide you a much better cooling than stock cooling.
It may be in this kind of thing, but it is up to you, but my advice is that your fan is performing well, but if you want to use the speed adjustment as in this picture or if you want to use it without overclocking in normal times, the constant high fan speed sound will disturb you.